View LTC1064-709_4867538.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LTC1064-7 Linear Phase, 8th Order Lowpass Filter
FEATURES

DESCRIPTIO
Steeper Roll-Off Than 8th Order Bessel Filters fCUTOFF up to 100kHz Phase Equalized Filter in 14-Pin Package Phase and Group Delay Response Fully Tested Transient Response Exhibits 5% Overshoot and No Ringing Wide Dynamic Range 72dB THD or Better Throughout a 50kHz Passband No External Components Needed Available in 14-Pin DIP and 16-Pin SO Wide Packages
The LTC(R)1064-7 is a clock-tunable monolithic 8th order lowpass filter with linear passband phase and flat group delay. The amplitude response approximates a maximally flat passband while it exhibits steeper roll-off than an equivalent 8th order Bessel filter. For instance, at twice the cutoff frequency the filter attains 34dB attenuation (vs 12dB for Bessel), while at three times the cutoff frequency, the filter attains 68dB attenuation (vs 30dB for Bessel). The cutoff frequency of the LTC1064-7 is tuned via an external TTL or CMOS clock. The LTC1064-7 features wide dynamic range. With single 5V supply, the S/N + THD is 76dB. Optimum 92dB S/N is obtained with 7.5V supplies. The clock-to-cutoff frequency ratio of the LTC1064-7 can be set to 50:1 (Pin 10 to V +) or 100:1 (Pin 10 to V -). When the filter operates at clock-to-cutoff frequency ratio of 50:1, the input is double-sampled to lower the risk of aliasing. The LTC1064-7 is pin-compatible with the LTC1064-X series, LTC1164-7 and LTC1264-7.
, LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.
APPLICATIO S

Data Communication Filters Time Delay Networks Phase-Matched Filters
TYPICAL APPLICATIO
1 VIN 2 3 7.5V 4 5 6 7 LTC1064-7 14 13 12 11 10 9 8
80kHz Linear Phase Lowpass Filter
-7.5V
7.5V VOUT
1064-7 TA01
NOTE: THE POWER SUPPLIES SHOULD BE BYPASSED BY A 0.1F CAPACITOR CLOSE TO THE PACKAGE AND ANY PRINTED CIRCUIT BOARD ASSEMBLY SHOULD MAINTAIN A DISTANCE OF AT LEAST 0.2 INCHES BETWEEN ANY OUTPUT OR INPUT PIN AND THE fCLK LINE.
1V/DIV
CLK = 4MHz
VS = 7.5V fCLK = 4MHz RATIO = 50:1
U
Eye Diagram
1s/DIV
1064-7 TA02
U
U
10647fb
1
LTC1064-7 ABSOLUTE AXI U RATI GS
Total Supply Voltage (V + to V -) .......................... 16.5V Power Dissipation ............................................. 400mW Burn-In Voltage ................................................... 16.5V Voltage at Any Input ..... (V - - 0.3V) VIN (V + + 0.3V) Storage Temperature Range ................ - 65C to 150C
PACKAGE/ORDER I FOR ATIO
TOP VIEW NC VIN GND V+ GND LP (A) INV (A) 1 2 3 4 5 6 7 14 RIN (A) 13 NC 12 V - 11 fCLK 10 50/100 9 8 VOUT NC
ORDER PART NUMBER LTC1064-7CN
N PACKAGE 14-LEAD PLASTIC DIP TJMAX = 110C, JA = 65C/W (N)
J PACKAGE 14-LEAD CERAMIC DIP TJMAX = 150C, JA = 65C/W (J)
OBSOLETE PACKAGE
Consider the N Package as an Alternate Source
LTC1064-7CJ LTC1064-7MJ
Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges.
The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C.VS = 7.5V, RL = 10k, TA = 25C, fCUTOFF = 10kHz or 20kHz, fCLK = 1MHz, TTL or CMOS level (maximum clock rise and fall time 1s) and all gain measurements are referenced to passband gain, unless otherwise specified. The filter cutoff frequency is abbreviated as fCUTOFF or fC.
PARAMETER Passband Gain Gain at 0.5 fCUTOFF Gain at 0.75 fCUTOFF Gain at fCUTOFF Gain at 2 fCUTOFF Gain with fCLK = 20kHz Gain with fCLK = 400kHz, VS = 2.375V Phase Factor (F ) Phase = 180 - F (f/fC) (Note 2) CONDITIONS 0.1Hz f 0.25 fCUTOFF fTEST = 5kHz, (fCLK /fC) = 50:1 fTEST = 10kHz, (fCLK /fC) = 50:1 fTEST = 5kHz, (fCLK /f C) = 100:1 fTEST = 15kHz, (fCLK /fC) = 50:1 fTEST = 20kHz, (fCLK /fC) = 50:1 fTEST = 10kHz, (fCLK /fC) = 100:1 fTEST = 40kHz, (fCLK /fC) = 50:1 fTEST = 20kHz, (fCLK /fC) = 100:1 fTEST = 200Hz, (fCLK /fC) = 100:1 fTEST = 4kHz, (fCLK /fC) = 50:1 fTEST = 8kHz, (fCLK /fC) = 50:1 0.1Hz f fCUTOFF (fCLK /fC) = 50:1 (fCLK /fC) = 100:1 (fCLK /fC) = 50:1 (fCLK /fC) = 100:1 MIN

ELECTRICAL CHARACTERISTICS
2
U
U
W
WW
U
W
(Note 1)
Operating Temperature Range LTC1064-7C ....................................... - 40C to 85C LTC1064-7M OBSOLETE .............. - 55C to 125C Lead Temperature (Soldering, 10 sec)................. 300C
TOP VIEW NC 1 VIN 2 GND 3 V+ 4 16 RIN (A) 15 NC 14 V - 13 NC 12 fCLK 11 50/100 10 NC 9 VOUT
ORDER PART NUMBER LTC1064-7CSW
GND 5 NC 6 LP (A) 7 INV (A) 8
SW PACKAGE 16-LEAD PLASTIC SO (WIDE) TJMAX = 110C, JA = 85C/W
TYP 0.10 - 0.35 - 0.35 -1.0 - 3.4 - 4.5 - 34.0 - 34.5 - 4.3 - 0.3 - 3.3 430 2.0 421 2.5 430 421
MAX 0.65 0.15 1.25 - 0.35 - 2.50 - 3.75 - 31.75 - 31.75 - 3.5 0.25 - 2.00
UNITS dB dB dB dB dB dB dB dB dB dB dB Deg Deg Deg Deg
10647fb
- 0.60 - 0.90 - 1.30 - 2.0 - 4.50 - 5.75 - 36.5 - 37.0 - 6.5 - 0.9 - 4.5

422 414
437 429
LTC1064-7
ELECTRICAL CHARACTERISTICS
PARAMETER Phase Nonlinearity (Notes 2, 4)
The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VS = 7.5V, RL = 10k, fCUTOFF = 10kHz or 20kHz, fCLK = 1MHz, TTL or CMOS level (maximum clock rise and fall time 1s) and all gain measurements are referenced to passband gain, unless otherwise specified. The filter cutoff frequency is abbreviated as fCUTOFF or fC.
CONDITIONS (fCLK /fC) = 50:1 (fCLK /fC) = 100:1 (fCLK /fC) = 50:1 (fCLK /fC) = 100:1 (fCLK /fC) = 50:1, f fCUTOFF (fCLK /fC) = 100:1, f fCUTOFF (fCLK /fC) = 50:1, f fCUTOFF (fCLK /fC) = 100:1, f fCUTOFF (fCLK /fC) = 50:1, f fCUTOFF (fCLK /fC) = 100:1, f fCUTOFF (fCLK /fC) = 50:1, f fCUTOFF (fCLK /fC) = 100:1, f fCUTOFF (fCLK /fC) = 50:1 (fCLK /fC) = 100:1 VS = 5V (AGND = 2V) VS = 5V VS = 7.5V 50:1 VS = 2.5V VS = 5V VS = 7.5V VS = 2.375V VS = 5V VS = 7.5V 50:1, VS = 5V 100:1, VS = 5V 50:1, VS = 5V 100:1, VS = 5V VS = 2.375V, TA = 25C VS = 5V, TA = 25C VS = 7.5V, TA = 25C Power Supply Range MIN TYP 1.0 1.0 MAX UNITS % % % % s s s s % % % % kHz kHz MHz MHz MHz VRMS VRMS VRMS VRMS k V V V mV mV V/C V/C mA mA mA mA mA mA V

2.0 2.0
Group Delay (td) td = (F /360)(1/ fC) (Note 3) Group Delay Deviation (Notes 3, 4)

58.6 115.0
59.7 0.5 117.0 1.0 59.7 117.0 1.0 1.0
60.7 119.0

2.0 2.0
Input Frequency Range (Table 9) Maximum fCLK
Clock Feedthrough (f fCLK) Wideband Noise (1Hz f fCLK) Input Impedance Output DC Voltage Swing (Note 5) Output DC Offset Output DC Offset TempCo Power Supply Current

25 1.0 2.1 3.0
70
220

17
2.375
22 22 26 28 28 32 8
10647fb
3
LTC1064-7
ELECTRICAL CHARACTERISTICS
Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: Input frequencies, f, are linearly phase shifted through the filter as long as f fC; fC = cutoff frequency. Figure 1 curve shows the typical phase response of an LTC1064-7 operating at fCLK = 1MHz, ratio = 50:1, fC = 20kHz and it closely matches an ideal straight line. The phase shift is described by: phase shift = 180 - F (f/fC); f fC. F is arbitrarily called the "phase factor" expressed in degrees. The phase factor allows the calculation of the phase at a given frequency. Example: The phase shift at 14kHz of the LTC1064-7 shown in Figure 1 is: phase shift = 180 - 430 (14kHz/20kHz) nonlinearity = -121 1% or -121 1.20. Note 3: Group delay and group delay deviation are calculated from the measured phase factor and phase deviation specifications. Note 4: Phase deviation and group delay deviation for LTC1064-7MJ is 4%. Note 5: The AC swing is typically 11VP-P, 7VP-P, 2.8VP-P, with 7.5V, 5V, 2.5V Supply respectively. For more information refer to the THD + Noise vs Input graphs.
180 90 0 -90 -180 -270 -360 0 2 4 6 8 10 12 14 16 18 20 FREQUENCY (kHz)
1164-7 F01
fCLK = 1MHz RATIO = 50:1
Figure 1. Phase Response in the Passband (Note 2)
PHASE (DEG)
10647fb
4
LTC1064-7
TYPICAL PERFOR A CE CHARACTERISTICS
Gain vs Frequency
10 0 -10 -20 -30 100:1 50:1
PHASE FACTOR 475 465 PHASE FACTOR 455 445 435 25C 485 VS = 5V (fCLK /fC) = 50:1 70C 465 70C 455 445 25C 435 0C 425 415 425 415 0.5 1.0 1.5 2.5 2.0 fCLK (MHz) 3.0 3.5 0.5 1.0 1.5 2.5 2.0 fCLK (MHz) 3.0 3.5 0C
GAIN (dB)
-40 -50 -60 -70 -80 -90 -100 -110 0.1 VS = 5V fCLK = 1MHz TA = 25C 1 10 FREQUENCY (kHz) 100
1064-7 G01
Phase Factor vs fCLK (Min and Max Representative Units)
445 VS = 5V TA = 25C (fCLK /fC) = 50:1
440
PHASE FACTOR
PHASE FACTOR
435
430
425
420 0.5 1.0 1.5 2.5 2.0 fCLK (MHz) 3.0 3.5
Passband Gain and Phase
3 2 1 0
GAIN (dB)
-1 -2 -3 -4 -5 -6 2 4 6 PHASE
- 60 -120 -180 -240 -300
GAIN (dB)
UW
Phase Factor vs fCLK (Typical Unit)
485 475
Phase Factor vs fCLK (Typical Unit)
VS = 5V (fCLK /fC) = 100:1
1064-7 G02
1064-7 G03
Phase Factor vs fCLK (Min and Max Representative Units)
445 VS = 5V TA = 25C PINS 3, 5 AT 2V (fCLK /fC) = 50:1
440
435
430
425
420 0.5 1.0 fCLK (MHz)
1064-7 G04
1.5
2.0
1064-7 G05
Passband Gain and Phase
180
3 2 1 0 -1 GAIN -2 PHASE -3 -4 -5 -6 2 4 6 -120 -180 -240 -300 -360 8 10 12 14 16 18 20 22 FREQUENCY (kHz)
1064-7 G07
180 VS = 5V fCLK = 2MHz (fCLK /fC) = 100:1 120 60 0 - 60
PHASE (DEG)
VS = 5V fCLK = 1MHz (fCLK /fC) = 50:1
120 60 0
PHASE (DEG)
GAIN
-360 8 10 12 14 16 18 20 22 FREQUENCY (kHz)
1064-7 G06
10647fb
5
LTC1064-7
TYPICAL PERFOR A CE CHARACTERISTICS
Passband Gain vs Frequency and fCLK
5 4 3 2
GAIN (dB)
5
VS = 7.5V TA = 25C (fCLK /fC) = 50:1
A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz D. fCLK = 4MHz E. fCLK = 5MHz
GAIN (dB)
GAIN (dB)
1 0 -1 -2 -3 -4 -5 10 100 10 FREQUENCY (kHz) 1000
1064-7 G08
D A BC E
Passband Gain vs Frequency and fCLK
5 4 3 2
GAIN (dB)
VS = SINGLE 5V TA = 25C (fCLK /fC) = 50:1
A. fCLK = 0.5MHz B. fCLK = 1.0MHz C. fCLK = 1.5MHz D. fCLK = 2.0MHz
DELAY (s)
0 -1 -2 A -3 -4 -5 1 10 FREQUENCY (kHz) 100
1064-7 G11
GAIN (dB)
1
B
CD -3 -4 -5 1
Delay vs Frequency and fCLK
250 A 200 VS = 5V TA = 25C (fCLK /fC) = 100:1
THD + NOISE (dB)
DELAY (s)
150
A. fCLK = 0.5MHz B. fCLK = 1.5MHz C. fCLK = 2.5MHz D. fCLK = 3.5MHz B
THD + NOISE (dB)
100
50 C D 0 1 6 11 26 16 21 FREQUENCY (kHz) 31 36
6
UW
1064-7 G14
Passband Gain vs Frequency and fCLK at TA = 85C
5 4 3 2 1 0 -1 -2 -3 -4 -5 1 100 10 FREQUENCY (kHz) 1000
1064-7 G09
Passband Gain vs Frequency and fCLK at TA = 85C
4 3 2 1 0 -1 -2 -3 -4 -5 1 10 FREQUENCY (kHz) 100
1064-7 G10
VS = 7.5V (fCLK /fC) = 50:1
A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz D. fCLK = 4MHz E. fCLK = 5MHz
VS = 5V (fCLK /fC) = 50:1
A. fCLK = 0.5MHz B. fCLK = 1.5MHz C. fCLK = 2.5MHz D. fCLK = 3.5MHz
D A BC E
A
B
CD
Passband Gain vs Frequency and fCLK at TA = 85C
5 4 3 2 1 0 -1 -2 VS = SINGLE 5V (fCLK /fC) = 50:1 A. fCLK = 0.5MHz B. fCLK = 1.0MHz C. fCLK = 1.5MHz D. fCLK = 2.0MHz
Delay vs Frequency and fCLK
125 A 100 VS = 5V TA = 25C (fCLK /fC) = 50:1 A. fCLK = 0.5MHz B. fCLK = 1.5MHz C. fCLK = 2.5MHz D. fCLK = 3.5MHz B C D 0
75
50
A
B
CD
25
10 FREQUENCY (kHz)
100
1064-7 G12
2
12
22 52 32 42 FREQUENCY (kHz)
62
72
1064-7 G13
THD + Noise vs Frequency
-40 -45 -50 -55 -60 -65 -70 -75 -80 -85 -90 1 FREQUENCY (kHz)
1064-7 G15
THD + Noise vs Frequency
-40 -45 -50 -55 -60 -65 -70 -75 -80 -85 -90 VS = 7.5V VIN = 1VRMS fCLK = 2.5MHz (fCLK /fC) = 50:1 (100k RESISTOR PIN 9 TO V - )
VS = 7.5V VIN = 2VRMS fCLK = 1MHz (fCLK /fC) = 50:1 (100k RESISTOR PIN 9 TO V - )
10
20
1
10 FREQUENCY (kHz)
50
1064-7 G16
10647fb
LTC1064-7
TYPICAL PERFOR A CE CHARACTERISTICS
THD + Noise vs Frequency
-40 -45 -50
THD + NOISE (dB)
THD + NOISE (dB)
THD + NOISE (dB)
-55 -60 -65 -70 -75 -80 -85 -90 1
VS = 5V VIN = 1VRMS fCLK = 1MHz (fCLK /fC) = 50:1 (100k RESISTOR PIN 9 TO V - )
10 FREQUENCY (kHz)
THD + Noise vs Input
-40 -45 -50 fIN = 1kHz fCLK = 1MHz (fCLK /fC) = 50:1 (100k PIN 9 TO V -) A. VS = 5V B. VS = 7.5V A B
-40 -45 -50
THD + NOISE (dB)
THD + NOISE (dB)
-60 -65 -70 -75 -80 -85 -90 0.1 1 INPUT (VRMS)
1064-7 G20
-60 -65 -70 -75 -80 -85
THD + NOISE (dB)
-55
THD + Noise vs Input
-40 -45 -50
THD + NOISE (dB) 5
PHASE DIFFERENCE (DEG)
4
POWER SUPPLY CURRENT (mA)
-55 -60 -65 -70 -75 -80 -85 -90 0.1
VS = SINGLE 5V fIN = 1kHz fCLK = 500kHz (fCLK /fC) = 100:1
A
A. PINS 3, 5 AT 2V B. PINS 3, 5 AT 2.5V 1 INPUT (VRMS)
1064-7 G23
UW
20
1064-7 G17
THD + Noise vs Frequency
-40 -45 -50 -55 -60 -65 -70 -75 -80 -85 -90 1 FREQUENCY (kHz)
1064-7 G18
THD + Noise vs Frequency
- 40 -45 - 50 - 55 - 60 -65 -70 -75 -80 -85 VS = SINGLE 5V VIN = 0.5VRMS fCLK = 500kHz (fCLK /fC) = 100:1 (PINS 3, 5 AT 2V)
VS = SINGLE 5V VIN = 0.5VRMS fCLK = 1MHz (fCLK /fC) = 50:1 (PINS 3, 5 AT 2V)
10
20
-90
1
2 3 FREQUENCY (kHz)
4
5
1064-7 G19
THD + Noise vs Input
-40
fIN = 1kHz fCLK = 2MHz (fCLK /fC) = 100:1 A. VS = 5V B. VS = 7.5V A B
THD + Noise vs Input
-45 -50 -55 -60 -65 -70 -75 -80 -85 A. PINS 3, 5 AT 2V B. PINS 3, 5 AT 2.5V 1 INPUT (VRMS)
1064-7 G21
-55
VS = SINGLE 5V fIN = 1kHz fCLK = 1MHz (fCLK /fC) = 50:1
A
B
5
-90 0.1
1 INPUT (VRMS)
5
-90 0.1
2
1064-7 G22
Phase Matching vs Frequency
48
PHASE DIFFERENCE BETWEEN ANY TWO UNITS (SAMPLE OF 50 REPRESENTATIVE UNITS) VS 5V fCLK 2.5MHz (fCLK /fC) = 50:1 OR 100:1 TA = 0C TO 70C
Power Supply Current vs Power Supply Voltage
44 40 36 32 28 24 20 16 12 8 4 0 -55C 25C 125C fCLK = 1MHz
B
3
2
1
2
0
0
0.2 0.6 0.8 0.4 FREQUENCY (fCUTOFF /FREQUENCY)
1.0
02
4 6 8 10 12 14 16 18 20 22 24 TOTAL POWER SUPPLY VOLTAGE (V)
1064-7 G25
1064-7 G24
10647fb
7
LTC1064-7
TYPICAL PERFOR A CE CHARACTERISTICS
Table 1. Passband Gain and Phase VS = 7.5V, (fCLK / fC) = 50:1, TA = 25C
FREQUENCY (kHz) fCLK = 1MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 fCLK = 2MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 fCLK = 3MHz (Typical Unit) 0.000 15.000 30.000 45.000 60.000 fCLK = 4MHz (Typical Unit) 0.000 20.000 40.000 60.000 80.000 fCLK = 5MHz (Typical Unit) 0.000 25.000 50.000 75.000 100.000 GAIN (dB) - 0.086 - 0.086 - 0.334 - 1.051 - 3.316 - 0.131 - 0.131 - 0.442 - 1.108 - 3.115 - 0.156 - 0.156 - 0.459 - 0.941 - 2.508 - 0.121 - 0.121 - 0.292 - 0.476 - 1.539 - 0.045 - 0.045 - 0.006 0.185 - 0.356 PHASE (DEG) 180.00 73.54 -33.60 -140.81 - 249.30 180.00 72.88 - 34.71 -141.99 - 250.45 180.00 72.54 - 35.01 - 141.95 - 250.53 180.00 72.12 - 35.75 - 142.92 - 252.63 180.00 70.85 - 38.25 - 146.77 - 259.27 FREQUENCY (kHz) fCLK = 4MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 fCLK = 5MHz (Typical Unit) 0.000 12.500 25.000 37.500 50.000 GAIN (dB) - 0.116 - 0.116 - 0.436 - 1.171 - 3.353 - 0.097 - 0.097 - 0.351 - 0.951 - 2.999 PHASE (DEG) 180.00 72.49 - 35.21 - 142.33 - 250.12 180.00 71.00 - 38.08 - 146.51 - 256.13
Table 2. Passband Gain and Phase VS = 7.5V, (fCLK / fC) = 100:1, TA = 25C
FREQUENCY (kHz) fCLK = 1MHz (Typical Unit) 0.000 2.500 5.000 7.500 10.000 fCLK = 2MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 fCLK = 3MHz (Typical Unit) 0.000 7.500 15.000 22.500 30.000 GAIN (dB) - 0.203 - 0.203 - 0.741 - 1.831 - 4.451 - 0.152 - 0.152 - 0.575 - 1.501 - 3.973 - 0.123 - 0.123 - 0.481 - 1.312 - 3.654 PHASE (DEG) 180.00 74.07 - 31.71 - 136.47 - 240.17 180.00 73.79 - 32.47 - 138.11 - 243.84 180.00 73.32 - 33.64 - 140.14 - 247.11
8
UW
Table 3. Passband Gain and Phase VS = 5V, (fCLK / fC) = 50:1, TA = 25C
FREQUENCY (kHz) fCLK = 0.5MHz (Typical Unit) 0.000 2.500 5.000 7.500 10.000 fCLK = 1MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 fCLK = 1.5MHz (Typical Unit) 0.000 7.500 15.000 22.500 30.000 fCLK = 2MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 fCLK = 2.5MHz (Typical Unit) 0.000 12.500 25.000 37.500 50.000 fCLK = 3MHz (Typical Unit) 0.000 15.000 30.000 45.000 60.000 GAIN (dB) - 0.081 - 0.081 - 0.345 - 1.063 - 3.283 - 0.071 - 0.071 - 0.322 - 1.036 - 3.284 - 0.095 - 0.095 - 0.392 - 1.075 - 3.155 - 0.127 - 0.127 - 0.447 - 1.041 - 2.856 - 0.126 - 0.126 - 0.411 - 0.864 - 2.397 - 0.102 - 0.102 - 0.292 - 0.546 - 1.769 PHASE (DEG) 180.00 73.71 - 33.31 - 140.36 - 248.52 180.00 73.44 - 33.83 - 141.13 - 249.68 180.00 73.03 - 34.53 - 141.89 - 250.45 180.00 72.81 - 34.70 - 141.77 - 250.24 180.00 72.61 - 34.91 - 141.88 - 250.62 180.00 72.23 - 35.64 - 142.96 - 252.73
10647fb
LTC1064-7
TYPICAL PERFOR A CE CHARACTERISTICS
Table 3. Passband Gain and Phase VS = 5V, (fCLK / fC) = 50:1, TA = 25C
FREQUENCY (kHz) fCLK = 3.5MHz (Typical Unit) 0.000 17.500 35.000 52.500 70.000 GAIN (dB) - 0.054 - 0.054 - 0.108 - 0.137 - 1.104 PHASE (DEG) 180.00 71.07 - 38.00 - 146.68 - 258.97
Table 4. Passband Gain and Phase VS = 5V, (fCLK / fC) = 100:1, TA = 25C
FREQUENCY (kHz) fCLK = 0.5MHz (Typical Unit) 0.000 1.250 2.500 3.750 5.000 fCLK = 1MHz (Typical Unit) 0.000 2.500 5.000 7.500 10.000 GAIN (dB) - 0.186 - 0.186 - 0.726 - 1.805 - 4.402 - 0.184 - 0.184 - 0.712 - 1.785 - 4.387 PHASE (DEG) 180.00 74.10 - 31.65 - 136.48 - 240.33 180.00 74.02 - 31.80 - 136.61 - 240.43 180.00 73.84 - 32.32 - 137.73 - 242.95 180.00 73.64 - 32.93 - 139.03 - 245.57 180.00 73.17 - 33.93 - 140.58 - 247.80 180.00 72.36 - 35.47 - 142.70 - 250.58 180.00 70.81 - 38.39 - 146.85 - 256.10
fCLK = 1.5MHz (Typical Unit) 0.000 - 0.145 3.750 - 0.145 7.500 - 0.596 11.250 - 1.556 15.000 - 4.047 fCLK = 2MHz (Typical Unit) 0.000 - 0.116 5.000 - 0.116 10.000 - 0.494 15.000 - 1.361 20.000 - 3.761 fCLK = 2.5MHz (Typical Unit) 0.000 - 0.101 6.250 - 0.101 12.500 - 0.452 18.750 - 1.273 25.000 - 3.611 fCLK = 3MHz (Typical Unit) 0.000 - 0.105 7.500 - 0.105 15.000 - 0.445 22.500 - 1.228 30.000 - 3.509 fCLK = 3.5MHzMHz (Typical Unit) 0.000 - 0.104 8.750 - 0.104 17.500 - 0.437 26.250 - 1.188 35.000 - 3.478
UW
Table 5. Passband Gain and Phase VS = Single 5V, (fCLK / fC) = 50:1, TA = 25C
FREQUENCY (kHz) fCLK = 0.5MHz (Typical Unit) 0.000 2.500 5.000 7.500 10.000 fCLK = 1MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 fCLK = 1.5MHz (Typical Unit) 0.000 7.500 15.000 22.500 30.000 fCLK = 2MHz (Typical Unit) 0.000 10.000 20.000 30.000 40.000 GAIN (dB) - 0.134 - 0.134 - 0.391 - 1.109 - 3.351 - 0.148 - 0.148 - 0.423 - 1.111 - 3.241 - 0.157 - 0.157 - 0.456 - 0.981 - 2.687 - 0.188 - 0.188 - 0.304 - 0.513 - 1.824 PHASE (DEG) 180.00 73.52 - 33.67 - 140.92 - 249.32 180.00 73.07 - 34.63 - 142.25 - 251.03 180.00 72.73 - 34.83 - 142.08 - 251.09 180.00 71.37 - 37.52 - 146.11 - 257.46
Table 6. Passband Gain and Phase VS = Single 5V, (fCLK / fC) = 100:1, TA = 25C
FREQUENCY (kHz) fCLK = 0.5MHz (Typical Unit) 0.000 1.250 2.500 3.750 5.000 fCLK = 1MHz (Typical Unit) 0.000 2.500 5.000 7.500 10.000 fCLK = 1.5MHz (Typical Unit) 0.000 3.750 7.500 11.250 15.000 fCLK = 2MHz (Typical Unit) 0.000 5.000 10.000 15.000 20.000 GAIN (dB) - 0.243 - 0.243 - 0.776 - 1.861 - 4.483 - 0.208 - 0.208 - 0.678 - 1.679 - 4.221 - 0.115 - 0.115 - 0.473 - 1.314 - 3.715 - 0.209 - 0.209 - 0.499 - 1.281 - 3.695 PHASE (DEG) 180.00 73.91 - 31.98 - 136.98 - 240.90 180.00 73.76 - 32.47 - 137.87 - 242.65 180.00 73.26 - 33.73 - 140.40 - 247.66 180.00 71.18 - 37.85 - 146.27 - 255.38
10647fb
9
LTC1064-7 PI FU CTIO S
Power Supply Pins (4, 12) The V (Pin 4) and the V (Pin 12) should be bypassed with a 0.1F capacitor to an adequate analog ground. The filter's power supplies should be isolated from other digital or high voltage analog supplies. A low noise linear supply is recommended. Using a switching power supply will lower the signal-to-noise ratio of the filter. The supply during power-up should have a slew rate less than 1V/s. When V + is applied before V - and V - is allowed to go above ground, a signal diode should clamp V - to prevent latch-up. Figures 2 and 3 show typical connections for dual and single supply operation.
V- 1 VIN V+ 2 3 4 5 0.1F 6 7 LTC1064-7 14 13 12 11 10 9 8 + GND DIGITAL SUPPLY V+ 200 CLOCK SOURCE 0.1F
+
Figure 2. Dual Supply Operation for an fCLK/fCUTOFF = 50:1
1 VIN V+ 0.1F 10k 2 3 4 5 6 7 LTC1064-7
10k
+
1F VOUT
1064-7 F03
Figure 3. Single Supply Operation for an fCLK/fCUTOFF = 50:1
Clock Input Pin (11) Any TTL or CMOS clock source with a square-wave output and 50% duty cycle (10%) is an adequate clock source for the device. The power supply for the clock source should not be the filter's power supply. The analog ground
10
U
U
U
-
for the filter should be connected to clock's ground at a single point only. Table 7 shows the clock's low and high level threshold values for a dual or single supply operation. A pulse generator can be used as a clock source provided the high level ON time is greater than 0.1s. Sine waves are not recommended for clock input frequencies less than 100kHz, since excessively slow clock rise or fall times generate internal clock jitter (maximum clock rise or fall time 1s). The clock signal should be routed from the right side of the IC package and perpendicular to it to avoid coupling to any input or output analog signal path. A 200 resistor between clock source and pin 11 will slow down the rise and fall times of the clock to further reduce charge coupling (Figures 2 and 3).
Table 7. Clock Source High and Low Threshold Levels
POWER SUPPLY Dual Supply = 7.5V Dual Supply = 5V Dual Supply = 2.5V Single Supply = 12V Single Suppl = 5V HIGH LEVEL 2.18V 1.45V 0.73V 7.80V 1.45V LOW LEVEL 0.5V 0.5V - 2.0V 6.5V 0.5V
VOUT
1064-7 F02
Analog Ground Pins (3, 5) The filter performance depends on the quality of the analog signal ground. For either dual or single supply operation, an analog ground plane surrounding the package is recommended. The analog ground plane should be connected to any digital ground at a single point. For dual supply operation, Pin 3 should be connected to the analog ground plane. For single supply operation pin 3 should be biased at 1/2 supply and should be bypassed to the analog ground plane with at least a 1F capacitor (Figure 3). For single 5V operation at the highest fCLK of 2MHz, Pin 3 should be biased at 2V. This minimizes passband gain and phase variations. Ratio Input Pin (10) The DC level at this pin determines the ratio of the clock frequency to the cutoff frequency of the filter. Pin 10 at V + gives a 50:1 ratio and Pin 10 at V - gives a 100:1 ratio. For single supply operation the ratio is 50:1 when Pin 10 is at V + and 100:1 when Pin 10 is at ground. When Pin 10 is not tied to ground, it should be bypassed to analog ground
10647fb
14 13 12 11 10 9 8 + GND DIGITAL SUPPLY 200 CLOCK SOURCE V+
LTC1064-7 PI FU CTIO S
with a 0.1F capacitor. If the DC level at Pin 10 is switched mechanically or electrically at slew rates greater than 1V/s while the device is operating, a 10k resistor should be connected between Pin 10 and the DC source. Filter Input Pin (2) The input pin is connected internally through a 40k resistor tied to the inverting input of an op amp. Filter Output Pins (9, 6) Pin 9 is the specified output of the filter; it can typically source 3mA and sink 1mA. Driving coaxial cables or resistive loads less than 20k will degrade the total harmonic distortion of the filter. When evaluating the device's distortion an output buffer is required. A noninverting buffer, Figure 4, can be used provided that its input common mode range is well within the filter's output swing. Pin 6 is an intermediate filter output providing an unspecified 6th order lowpass filter. Pin 6 should not be loaded. External Connection Pins (7, 14) Pins 7 and 14 should be connected together. In a printed circuit board the connection should be done under the IC package through a short trace surrounded by the analog ground plane. NC Pins (1, 5, 8, 13) Pins 1, 5, 8 and 13 are not connected to any internal circuit point on the device and should preferably be tied to analog ground.
Figure 4. Buffer for Filter Output
APPLICATI
S I FOR ATIO
Clock Feedthrough Clock feedthrough is defined as the RMS value of the clock frequency and its harmonics that are present at the filter's output pin (9). The clock feedthrough is tested with the input pin (2) grounded and it depends on PC board layout and on the value of the power supplies. With proper layout techniques the values of the clock feedthrough are shown in Table 8.
Table 8. Clock Feedthrough
VS Single 5V 5V 7.5V 50:1 90VRMS 100VRMS 120VRMS 100:1 100VRMS 300VRMS 650VRMS
amplitude strongly depends on scope probing techniques as well as grounding and power supply bypassing. The clock feedthrough, if bothersome, can be greatly reduced by adding a simple R/C lowpass network at the output of the filter pin (9). This R/C will completely eliminate any switching transients. Wideband Noise The wideband noise of the filter is the total RMS value of the device's noise spectral density and it is used to determine the operating signal-to-noise ratio. Most of its frequency contents lie within the filter passband and it cannot be reduced with post filtering. For instance, the LTC1064-7 wideband noise at 5V supply is 105VRMS, 95VRMS of which have frequency contents from DC up to the filter's cutoff frequency. The total wideband noise (VRMS) is nearly independent of the value of the clock. The clock feedthrough specifications are not part of the wideband noise.
10647fb
Note: The clock feedthrough at single 5V is imbedded in the wideband noise of the filter. Clock waveform is a square wave.
Any parasitic switching transients during the rise and fall edges of the incoming clock are not part of the clock feedthrough specifications. Switching transients have frequency contents much higher than the applied clock; their
+
1k
-
U
W
U
U
UO
U
U
LT1220
1064-7 F04
11
LTC1064-7
APPLICATI
S I FOR ATIO
Speed Limitations To avoid op amp slew rate limiting at maximum clock frequencies, the signal amplitude should be kept below a specified level as shown in Table 9.
POWER SUPPLY 7.5V
5V Single 5V
MAXIMUM fCLK 5.0MHz 4.5MHz 4.0MHz 3.5MHz 3.5MHz 3.0MHz 2.0MHz
MAXIMUM VIN 1.8VRMS (fIN > 80kHz) 2.3VRMS (fIN > 80kHz) 2.7VRMS (fIN > 80kHz) 1.4VRMS (fIN > 500kHz) 1.6VRMS (fIN > 80kHz) 0.7VRMS (fIN > 400kHz) 0.5VRMS (fIN > 250kHz)
2V/DIV
Table 9. Maximum VIN vs VS and Clock
Table 10. Transient Response of LTC Lowpass Filters
DELAY RISE SETTLING TIME* TIME** TIME*** LOWPASS FILTER (SEC) (SEC) (SEC) LTC1064-3 Bessel 0.50/fC 0.34/fC 0.80/fC LTC1164-5 Bessel 0.43/fC 0.34/fC 0.85/fC LTC1164-6 Bessel 0.43/fC 0.34/fC 1.15/fC LTC1264-7 Linear Phase 1.15/fC 0.36/fC 2.05/fC LTC1164-7 Linear Phase 1.20/fC 0.39/fC 2.2/fC LTC1064-7 Linear Phase 1.20/fC 0.39/fC 2.2/fC LTC1164-5 Butterworth 0.80/fC 0.48/fC 2.4/fC LTC1164-6 Elliptic 0.85/fC 0.54/fC 4.3/fC LTC1064-4 Elliptic 0.90/fC 0.54/fC 4.5/fC LTC1064-1 Elliptic 0.85/fC 0.54/fC 6.5/fC * To 50% 5%, ** 10% to 90% 5%, *** To 1% 0.5% OVERSHOOT (%) 0.5 0 1 5 5 5 11 18 20 20
ts INPUT 90% OUTPUT
Table 11. Aliasing (fCLK = 100kHz)
INPUT FREQUENCY (VIN = 1VRMS, fIN = fCLK fOUT) (kHz) 50:1, fCUTOFF = 2kHz 190 (or 210) 195 (or 205) 196 (or 204) 197 (or 203) 198 (or 202) 199.5 (or 200.5) 100:1, fCUTOFF = 1kHz 97 (or 103) 97.5 (or 102.5) 98 (or 102) 98.5 (or 101.5) 99 (or 101) 99.5 (or 100.5) OUTPUT LEVEL (Relative to Input, 0dB = 1VRMS) (dB) -76.1 - 51.9 - 36.3 - 18.4 - 3.0 - 0.2 -74.2 - 53.2 - 36.9 - 19.6 - 5.2 - 0.7 OUTPUT FREQUENCY (Aliased Frequency fOUT = ABS [fCLK fIN]) (kHz)
10.0 5.0 4.0 3.0 2.0 0.5 3.0 2.5 2.0 1.5 1.0 0.5
12
U
Transient Response
50s/DIV VS = 7.5V, fIN = 2kHz 3V fCLK = 1MHz, RATIO = 50:1
1064-7 F05
W
U
UO
Figure 5.
50%
td
10%
tr
RISE TIME (tr) =
0.39 5% fCUTOFF 2.2 SETTLING TIME (ts) = 5% f (TO 1% of OUTPUT) CUTOFF 1.2 DELAY TIME (td) = GROUP DELAY fCUTOFF (TO 50% OF OUTPUT)
1064-7 F06
Figure 6.
Aliasing Aliasing is an inherent phenomenon of sampled data systems and it occurs when input frequencies close to the sampling frequency are applied. For the LTC1064-7 case at 100:1, an input signal whose frequency is in the range of fCLK 3%, will be aliased back into the filter's passband. If, for instance, an LTC1064-7 operating with a 100kHz clock and 1kHz cutoff frequency receives a 98kHz, 10mV input signal, a 2kHz, 143VRMS alias signal will appear at its output. When the LTC1064-7 operates with a clock-tocutoff frequency of 50:1, aliasing occurs at twice the clock frequency. Table 11 shows details.
10647fb
LTC1064-7
PACKAGE DESCRIPTIO
.300 BSC (7.62 BSC)
.008 - .018 (0.203 - 0.457)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS
U
J Package 14-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
.785 (19.939) MAX 14 13 12 11 10 9 8 .005 (0.127) MIN .025 (0.635) RAD TYP .220 - .310 (5.588 - 7.874) 1 2 3 4 5 6 7 .200 (5.080) MAX .015 - .060 (0.381 - 1.524) 0 - 15 .045 - .065 (1.143 - 1.651) .014 - .026 (0.360 - 0.660) .100 (2.54) BSC .125 (3.175) MIN
J14 0801
OBSOLETE PACKAGE
10647fb
13
LTC1064-7
PACKAGE DESCRIPTIO
.300 - .325 (7.620 - 8.255)
.008 - .015 (0.203 - 0.381) +.035 .325 -.015 .005 (0.127) .100 MIN (2.54) BSC
(
+0.889 8.255 -0.381
)
INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
NOTE: 1. DIMENSIONS ARE
14
U
N Package 14-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.770* (19.558) MAX 14 13 12 11 10 9 8 .255 .015* (6.477 0.381) 1 .130 .005 (3.302 0.127) .020 (0.508) MIN 2 3 4 5 6 7 .045 - .065 (1.143 - 1.651) .065 (1.651) TYP .120 (3.048) MIN .018 .003 (0.457 0.076)
N14 1103
10647fb
LTC1064-7
PACKAGE DESCRIPTIO
.030 .005 TYP N
.420 MIN
1
2
3
RECOMMENDED SOLDER PAD LAYOUT 1 .291 - .299 (7.391 - 7.595) NOTE 4 .010 - .029 x 45 (0.254 - 0.737)
0 - 8 TYP
.005 (0.127) RAD MIN
.009 - .013 (0.229 - 0.330)
NOTE 3 .016 - .050 (0.406 - 1.270)
NOTE: 1. DIMENSIONS IN
INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS 4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
SW Package 16-Lead Plastic Small Outline (Wide .300 Inch)
(Reference LTC DWG # 05-08-1620)
.050 BSC .045 .005 .398 - .413 (10.109 - 10.490) NOTE 4 16 15 14 13 12 11 10 9 N .325 .005 NOTE 3 .394 - .419 (10.007 - 10.643) N/2 N/2 2 3 4 5 6 7 8 .093 - .104 (2.362 - 2.642) .037 - .045 (0.940 - 1.143) .050 (1.270) BSC .004 - .012 (0.102 - 0.305) .014 - .019 (0.356 - 0.482) TYP
S16 (WIDE) 0502
10647fb
15
LTC1064-7
TYPICAL APPLICATIO U
Eye Diagram
-7.5V 7.5V VOUT
1064-7 TA01
80kHz Linear Phase Lowpass Filter
1 VIN 2 3 7.5V 4 5 6 7 LTC1064-7 14 13 12 11 10 9 8
NOTE: THE POWER SUPPLIES SHOULD BE BYPASSED BY A 0.1F CAPACITOR CLOSE TO THE PACKAGE AND ANY PRINTED CIRCUIT BOARD ASSEMBLY SHOULD MAINTAIN A DISTANCE OF AT LEAST 0.2 INCHES BETWEEN ANY OUTPUT OR INPUT PIN AND THE fCLK LINE.
1V/DIV
VS = 7.5V fCLK = 4MHz RATIO = 50:1
CLK = 4MHz
1s/DIV
1064-7 TA02
RELATED PARTS
PART NUMBER LTC1064 LTC1064-1/2/3/4 LTC1164 LTC1164-5/6/7 LTC1264 LTC1264-7 LT6600-2.5 LT6600-10 DESCRIPTION Universal Filter Building Block 8th Order Low Pass Filters, FO Max = 100kHz Universal Filter Building Block 8th Order Low Pass Filters, FO Max = 20kHz Universal Filter Building Block 8th Order Low Pass Filter, FO Max = 200kHz Low Noise Differential Amp and 10MHz Lowpass Low Noise Differential Amp and 20MHz Lowpass COMMENTS Allows for Bandpass (Up to 50kHz) Using External Resistors Elliptic, Butterworth, Bessel, Cauer Allows for Bandpass (Up to 20kHz) Using External Resistors Butterworth, Bessel or Elliptic Allows for Bandpass (Up to 100kHz) Using External Resistors Flat Group Delay, High Speed Lowpass Filter 55VRMS Noise 100kHz to 10MHz 3V Supply 86VRMS Noise 100kHz to 20MHz 3V Supply
10647fb
16
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 FAX: (408) 434-0507
LT/LT 0905 REV B * PRINTED IN USA
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 1992

▲Up To Search▲

Price & Availability of LTC1064-709

	To Download LTC1064-709 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .